Convolution

Convolution is another Stewart Coffin design, and is numbered 30 in his numbering Scheme. Originally produced in 1980 the seven dissimilar pieces can be assembled in one way, and one way only to give a 4x4x4 cube with a symmetrical pattern on all faces.

Convolution designed by Stewart Coffin made by Brian Menold

Convolution designed by Stewart Coffin made by Brian Menold

This version was made by Brian Menold over at Wood Wonders and is made entirely of Zebra Wood. The puzzle is a nice size at 1 7/8″ and the choice of Zebra Wood really helps to show off the symmetry on each side. This is a very nicely made puzzle, at a very good price.

You may remember from my post about the MMMM’s puzzle that I received from Brian when ordering the convolution that there were some issues in Brian’s view when I was ordering. Brian normally makes the Convolution in either Oak or Poplar, and the puzzle is slightly larger. When I contacted Brian about buying a copy of Convolution from him, he got in touch to say he had a few copies in rarer hardwoods which were slightly smaller but the same price if I was interested. I thought this was a great offer, and took him up on it.

After a little back and forth conversation via email, we settled on the Zebra Wood version, however there were a few hiccups along the way which led to Brian sending me the MMMM’s free. Originally when he told me about the puzzles he had, he’d looked at his Involution puzzles, as they are so similar, so it turned out he didn’t have the wood combination he thought he had. He really didn’t have to, and to my mind there were no issues at all. Just goes to show that Brian’s a really decent guy and I highly recommend both his work and him as a person to buy from.

The seven pieces of Convolution

The seven pieces of Convolution

Getting back to the puzzle itself, this is a classic Coffin reproduction, and is well made. The pieces have a tight fit, and are simply finished with a wax, so there are no stains or other products to tarnish this beautiful wood being used. The puzzle itself creates an interlocking cube so unlike many other cubic dissections, this one doesn’t need a box to hold the pieces, and isn’t going to fall apart if someone bumps into it.

The fact that the pieces are interlocking also adds to the complexity of solving the puzzle. There is only one assembly, and the symmetrical pattern on each side does help with the assembly to some extent. This would be a tough puzzle if it was sent unassembled, and looking at a picture of the assembled cube isn’t going to give a clue as to where certain pieces should be. This is a great design, and while it may not stand out on the puzzle shelf amongst other flashier puzzles, this is one that you really want to pick up and solve.

4 thoughts on “Convolution

  1. Eddie

    Neil,

    It is a great news that your thumb is on the way to recovery. Wish you the best. I enjoy reading your blog and following your journey into puzzle-making craftsmanship. I notice a lot of end-grain gluing with these cubes, and in general woodworking realm, end-grain glue joints are considered weak and destined to fail after a while (years?). So, what is your take on that and do you do anything special (per-treatment of sort or adding extra glue, etc.)? Are tight-grain woods used more for the cube construction (for absorbing the glue less, perhaps) or does it matter?

    Reply
    1. thejuggler Post author

      Hi Eddie, There’s a lot of differing opinions in about gluing endgrain joints, as with everything in woodworking. From my limited experience, and discussion with other puzzle makers, it tends not to be an issue. Depending on the joint, clamping can help, and I tend to find that for an endgrain joint, I use slightly more glue as more is soaked up my the grain. For something like the convolution, the entire puzzle is clamped tightly during the time the glue is drying, and I’ve not had any issues. Something that some puzzle makers do on these sort of joints is to add splines, which gives a non-endgrain surface to glue to. Really it depends on the puzzle, as not all are suited to this type of joint, nor would they look right.

      In terms of wood choice, for the most part it’s more an aesthetic choice than a density choice, but again I’ve not had issues, and know of other puzzle craftsmen who’ve had puzzles with endgrain joints and after many years have had no issues.

      Reply
  2. George Geissler

    I have been looking for something to make after I have downsized my wood turning adventures. It has been some time since I have played with puzzles. I hope that I am able to make and solve it. How can I get in touch with Brian?

    George

    Reply
  3. George Geissler

    My experience with end grain gluing is that it is necessary to use a special procedure. I have a jar of 50% glue that is used on the end grain after it is cleaned with acetone to remove the oils from exotic woods. Of course the glue should be allowed to cure for a reasonable amount of time. Now the end grain piece is ready to be glued to a face grain piece. I always use clamps when possible. Joints made using pressure are always stronger. This is my experience with end grain glued joints.

    Reply

Leave a Reply to George GeisslerCancel reply