Wil’s Aluminium Cylinder

The Aluminium Cylinder is another intriguing puzzle from Wil Strijbos in the Netherlands. Wil has been making metal puzzles for quite some time now, and the quality of his work is excellent. Have a look at my review of Wil’s first ever puzzle design The Aluminium Cross, to see where it all started.

Aluminium Cylinder by Wil Strijbos

Aluminium Cylinder by Wil Strijbos

The object of the puzzle is to remove the lid from the cylinder. The lid will spin 360 degrees in either direction, can be depressed a new millimetres, and the puzzle rattles when you shake it. Other than this, there is a small hole in the bottom of the puzzle which allows you to see into the middle of the puzzle. This hole isn’t much use, but does allow you to see a feature at the far end of the hole which must be useful. Finally, laser engraved into the side of the puzzle are two numbers. These relate to the particular run of the puzzle, and the puzzle number within that run. They may also be useful in solving the puzzle, but I couldn’t comment on that 😉

When I started playing with this, I didn’t seem to make a lot of progress. The puzzle will go silent as you move it around in your hands, then you hear things rattle when you press the lid down. None of this seems to do much other than confuse. After a while I managed to do something useful, and a ball bearing appeared in the hole in the middle of the puzzle. I confess that at this point, I had no idea what I’d done, or how to replicate it. Turning the puzzle upside down and looking in the hole, I watched the ball bearing disappear into the feature at the top of the hole, and it was gone again.

Much puzzling later, I managed to get the ball back out, and again had no idea how I’d done this. I looked at the puzzle when the ball appeared, and tried to figure out what I’d done differently. I still had no idea at this point, and repeating it seemed beyond me. So it was time to think! (c) Allard

Some time later, I finally figured out what was going on, and a few minutes later, the lid popped up with a satisfying sound. Once open the locking mechanism is fully visible, and you’ll be amazed as to just how simple it is. This is a wonderful mechanism, and my hat is off to Wil for creating this. Reversing the opening process closes the puzzle, and returns it to its starting state, ready to confound the next unsuspecting puzzler.

I can now open the puzzle in around 10 seconds, however shutting it still takes me a little longer. For some reason it’s not as simple to close as it is to open!

This is a great puzzle, and highly recommended for any puzzler. Be warned though, this may take a lot of time to solve!

7 thoughts on “Wil’s Aluminium Cylinder

  1. Kevin

    Hi Neil,

    I found this one very tough – it took me nearly a week to do it. I also couldn’t quite work out how I did the key move. I felt terrible when a friend at work managed it in under 2 hours!!! Apparently some people have been unable to solve it after months. I still love doing this one however – it gives a peculiar satisfaction when it pops open.

    Reply
  2. Ryan Marciano

    Im not sure if I broke mine. The lid barely turns and will actually snap down. I think maybe some balls are locked next to each other? I dobt want a hint or sokution. Just feels like I broke it or got it stuck. Heard of this?

    Reply
    1. thejuggler Post author

      Doesn’t sound like something which should happen with the puzzle. From knowing the design, there’s not much that can stick, or lock up.

      Reply
      1. Lender

        Is there a solution to this? I just received mine the other day and a friend tried their luck and gave it back with the same description as given above.

        Reply
    1. thejuggler Post author

      Once you have opened it, there is no space inside to store anything. The inner space is required for the puzzle mechanism.

      Reply
  3. Robert Kahrl

    When I set aside a block of time to focus on it, and started to manipulate the position of the ball and the lid, all of a sudden it popped open. It took about 25 minutes. I’m not sure how I did it, but in order to get it back together again, I’ll have to figure it out.

    Reply

Leave a Reply to thejugglerCancel reply